Years of testing have proven this unique finish to be the most advanced, highly engineered single-part formulation, based on urethane-alkyd resins available. It provides incredibly hard urethane abrasion and chemical resistance with outstanding gloss, durability, colour retention and U.V.protection.
In order to keep the voltage drop in the cable as low as possible and to avoid unacceptable heating of
the cable, it is necessary to carefully determine the required cable cross-sections. The voltage (V) drop between
current source and consumer must not exceed the following values:
Position lanterns: 5% in 12 V on-board network = 0.60 V Other consumers: 7% in the 12 V on-board
network = 0.84 V
Since the current has an outward and return path through 2 cores, the length of the conductor is always
as long as the cable length. The constant conductance of copper is 56.
Length (m)
Double length (m)
(two-wire)
Consumption (W)
Voltage (A)
Voltage drop (%)
Voltage drop (V)
Volt (12 V)
Volt (24 V)
Machine room use
You will need:
mm²
(due to the maximum current carrying capacity)
mm²
(due to the maximum voltage drop)
Cables with this cross section are not available in normal specialized trade.
We recommend a cable with at least
mm² Cross section
Years of testing have proven this unique finish to be the most advanced, highly engineered single-part formulation, based on urethane-alkyd resins available. It provides incredibly hard urethane abrasion and chemical resistance with outstanding gloss, durability, colour retention and U.V.protection.
Product beschrijving
Years of testing have proven this unique finish to be the most advanced, highly engineered single-part formulation, based on urethane-alkyd resins available. It provides incredibly hard urethane abrasion and chemical resistance with outstanding gloss, durability, colour retention and U.V.protection. It can be applied directly on degreased and sanded fiberglass, 1-component primers and topcoats, as well as on thoroughly sanded 2-component polyurethanes.
Processing instructions
For coated surfaces:
Remove growth from the substrate and carefully degrease. Sand the surface thoroughly, clean well and allow to dry. Remove rust and dust before application. Then apply 1-3 coats of Mono-Urethane.
For uncoated surfaces:
GRP: Apply 1-2 coats of Multiprimer. Allow the primer to dry and sand with 220 grit. Then apply approx. 3 coats of Mono-Urethane.
Steel: Apply 3 coats of Multiprimer. Allow the primer to dry and sand with 220 grit. Then apply approx. 3 coats of Mono-Urethane.
Wood: Apply 1-2 coats of Multiprimer. Allow the primer to dry and sand with 220 grit. Then apply approx. 3 coats of Mono-Urethane.
Aluminium: Apply 1-2 coats of Multiprimer. Allow the primer to dry and sand with 220 grit. Then apply approx. 3 coats of Mono-Urethane.
Drying time at 20 °C: 1 hour Processing time at 20 °C: min. 24 hours Processing temperature: +10 °C to max. 28 °C
Product safety
Please note the following hazard warnings:
Hazard pictograms
Signal word
Waarschuwing
Hazard warnings
Ontvlambare vloeistof en damp.
Buiten het bereik van kinderen houden.
Verwijderd houden van warmte/vonken/open vuur/hete oppervlakken. – Niet roken.
Stof/rook/gas/nevel/damp/spuitnevel niet inademen.
Alleen buiten of in een goed geventileerde ruimte gebruiken.
Beschermende handschoenen/beschermende kleding/oogbescherming/gelaatsbescherming dragen.
NA INSLIKKEN: onmiddellijk een ANTIGIFCENTRUM of een arts raadplegen.
BIJ CONTACT MET DE HUID (of het haar): verontreinigde kleding onmiddellijk uittrekken – huid met water afspoelen/afdouchen.
Inhoud/verpakking afvoeren naar …
Herhaalde blootstelling kan een droge of een gebarsten huid veroorzaken.
Ask other SVB customers who have already purchased this product from us for your experience.
Your question will be automatically forwarded to other SVB customers and your question will be published on the product page. Please do not pose any questions which can only be answered by the SVB team – such as the status of an order or product availability. You are also more than welcome to contact our SVB team by email at: info@svb24.com or by phone at: +49 (0)421-57290-0 .
More "Customers ask customers" available in the following available languages
:
No questions asked yet. Be the first to ask a question!