BEPMARINE

All-Purpose Tank Sensor TS1

Reset image position
Close
Terug
Art.nr. 14285
Op voorraad
SVB Price: € 167,72
You save: 9%
€ 184,96
Inc. tax, ex. shipping.
pcs.
€ 167,72 Inc. tax, ex. shipping.

Add now

Invalid value

Buy
Art.nr.
14285
EAN
00870216038476
Model nr.
MV-TS1
Omschrijving
BEPMARINE - All-Purpose Tank Sensor TS1

Product beschrijving

*** The fuel level sensor data sheet is available in our downloads section ***

The universal ultrasonic sensor TS1 is usable for fuel, drinking water and sewage tanks. No more incorrect display, as there will be no deposits an the sensor. Easy installation on standard SAE 5 tank flange.
We will programm the sensor according to the size of your tank that you will send us with the data sheet available on the download section of this web site. The device can be connected to instruments from VDO, Faria, Teleflex, etc.
Note: For replacement of capacitive measuring VDO sensors, the optional voltage divider (art. no. 15060) is required (sold separately).
Please pay attention:
When using an existing VDO dirt or freshwater instrument, the capacitively operating VDO-fuel sender is to be replaced by the programmable TS1 ultrasonic level transmitter; and the SVB-voltage divider No. 15060 must also be installed.  
  
Delivery contents: sensor, cork / Viton seal, 5 washers.
  • 10 - 32 volts (12 v / 24 v electrical system)
  • tank depth: 200 to 2000 mm
  • distance from the middle of the sensor to the tank walls or splash guard: at least 150 mm
  • programmable output for ohmic or DC values ​​(10 - 180 ohms, 10 - 300 ohms, 240 - 33 ohm, 0 - 5 volts)
  • temperature range: 4 - 65°C
  • for metal and plastic tanks
  • suitable for fuel, diesel, fresh and gray water and sewage
  • attachment according to SAE5 standard (5 holes in a hole diameter of 53 mm)
  • installation requirements: at least 42 mm diameter filler neck / minimum distance to the tank sides 150 mm / install parallel to the media surface
  • optional M4 screws for installation required, length depending on tank / installation situation
  • electrical connection: 3 wires with open end, about 15cm long / red: PLUS electrical system, black: MINUS electrical system, green: sensor output to the instrument
*** Please use the data sheet in our download area for programming***

Note:
  • The device has to be programmed by us. Please fill out the data sheet in our download area. This service is free of charge for you. If you want to have your tank sensor TS1 reprogrammed for another tank, we have to charge our programing fee.
 
  • The medium itself, the temperature, the viscosity and the surface condition of the medium (for example, air bubbles) can affect the measurement results.
 
  • In conjunction with SIMARINE Pico battery / system monitors, the output signal must be programmed at "0 - 5 Volt" and the TS1 must be connected to a voltage measurement input of the Pico.
 
  • Although some of the tanks of the manufacturer CAN have a connection fitting with SAE-5 flange / holes, the TS1 cannot be mounted directly on the connecting fitting, as its housing would collide with the surrounding connections. By using the asdapter item 21594 mounting would be possible. For this purpose, the threaded holes inside the adapter must be drilled and the TS1 including its seal fixed on the tank with long mounting screws. When programming the TS1, the value of the top limit must be set at a minimum of 30 mm.

Documenten

de-flag
Datablad
PDF, 603,07 KB
de-flag
Korte handleiding
PDF, 171,35 KB
fr-flag
Datablad
.PDF, 366,62 KB
en-flag
Handleiding
.PDF, 523,60 KB
en-flag
Korte handleiding
PDF, 10,20 MB
it-flag
Handleiding
PDF, 484,49 KB
multi-flag
Handleiding
PDF, 63,65 KB

Customers ask customers

Ask other SVB customers who have already purchased this product from us for your experience.

Your question will be automatically forwarded to other SVB customers and your question will be published on the product page. Please do not pose any questions which can only be answered by the SVB team – such as the status of an order or product availability. You are also more than welcome to contact our SVB team by email at: info@svb24.com or by phone at: +49 (0)421-57290-0 .

  • More "Customers ask customers" available in the following available languages :
  • Deutsch
  • English
  • Français
No questions asked yet. Be the first to ask a question!

Klantenwaarderingen

Average customer rating

Average Price-to-performance ratio
Average Quality / Processing ratio
Average satisfaction with this product

Rating overview

5 Stars
(2)
4 Stars
(5)
3 Stars
(1)
2 Stars
(0)
1 Stars
(0)
Finland
25-04-2019
prijs-kwaliteitverhouding
Klantenservice en advies
Satisfaction with this product

This rating belongs to item no. 14285

interesting
not connected yet but ity looks very good and good quality
Vertaal deze tekst
Duitsland
10-10-2017
prijs-kwaliteitverhouding
Klantenservice en advies
Satisfaction with this product

This rating belongs to item no. 14285

Duitsland
04-07-2019
prijs-kwaliteitverhouding
Klantenservice en advies
Satisfaction with this product

This rating belongs to item no. 15060

Der Tankgeber funktioniert einwandfrei. Jedoch passte der mitgelieferte Spannungsteiler nicht zu meinen - in der Bestellung angegebenen VDO Instrumenten - , so daß ich einen eigenen Sannungsteiler bauen mußte. .
Vertaal deze tekst
Duitsland
04-09-2011
prijs-kwaliteitverhouding
Klantenservice en advies
Satisfaction with this product
einfacher Einbau und präzise Messung.
Vertaal deze tekst
Duitsland
22-04-2011
prijs-kwaliteitverhouding
Klantenservice en advies
Satisfaction with this product
nachdem ich mehrere verschiedene Geber für die Tankanzeige Frischwasser ausprobierte hab ich nun endlich einen hervorragenden Geber gefunden. Die Tankanzeige funktioniert jetzt endlich sehr gut. Dank auch an das Team von SVB, die die Einstellung des Gebers vornahmen.
Vertaal deze tekst
Finland
03-09-2010
prijs-kwaliteitverhouding
Klantenservice en advies
Satisfaction with this product
Duitsland
10-05-2010
prijs-kwaliteitverhouding
Klantenservice en advies
Satisfaction with this product
Das Gerät ist gut, die Erfahrung wird es zeigen, der Spannungsausgang geht über einen Emitterfolger (Transistor) und einen 100 Ohm Widerstand auf ein VDO Instrument mit 4 bis 20 mA, das funktioniert. Für den Sensor habe ich ein Schallführungsrohr 40mm bis auf die Tanksohle eingebaut, dann schabbelt es nicht für den Sensor, die Praxis wird es zeigen. Der 5 Loch-Flansch ist ein Leckerbissen!!!
Vertaal deze tekst
Toon alle beoordelingen